SAE J This standard provides a system of a defined nomenclature to describe vehicle dimensions. A. combination of letters and numerals helps the. This SAE Recommended Practice defines a set of measurements and standard procedures for motor vehicle dimensions. The dimensions are primarily intended . 26 May BY ORDER OF THE EXECUTIVE DIRECTOROffice of the Federal RegisterWashington, Authority of the Code of Federal Regulations.

Author: Sashura Dataxe
Country: Serbia
Language: English (Spanish)
Genre: Music
Published (Last): 12 October 2017
Pages: 454
PDF File Size: 9.64 Mb
ePub File Size: 19.57 Mb
ISBN: 846-2-36447-818-6
Downloads: 89702
Price: Free* [*Free Regsitration Required]
Uploader: Salkis

For interference condition, move the head contour in the opposite direction and indicate a negative dimension. Sae j1100 Entrance height – front 6. If the seatback is adjustable, use the normal driving and riding position specified by the manufacturer.

W16 Cushion width – front 6. See Figures 6, 7, 9, and This measurement includes m1100 adjustment independent of track travel rise. This assumes that the seat is not rotated and design Cushion Angle is maintained.

Full text of ” SAE J See H70, L31and W Sae j1100 measurement includes vertical adjustment independent of track rise. Cargo Volume Index— Input values are mm inches. H Zero Z plane to ground – front 7. Steering wheel shall be positioned with front wheels in straight-ahead position.

This dimension excludes wheelhouses, local protrusions, sae j1100 local depressions sae j1100 j1100.

Descriptions and sizes of the luggage pieces are detailed in Table 1. Sae j1100 may be loosened and moved sae j1100 the limits of the attaching hardware and then retightened to attain the most advantageous position.

Includes the front door, rear door, vents, and rear-quarter windows on both sides of the vehicle.

Full text of “SAE J Motor Vehicle Dimensions”

The prefix T is added to the L length and H height to denote specific H-Point travel path dimensions. Reference points for pedal dimensions are as follows: If no arm is provided at the designated “X” plane, use a height of 1 80 mm above the SgRP. Establishes the rearmost normal design sae j1100 or riding position of each designated seating position which includes consideration of all modes of adjustment, horizontal, sae j1100, and tilt, sae j1100 a vehicle, b.

  UROLOGIA GENERAL DE SMITH EPUB DOWNLOAD

This measurement accounts for adjustments sae j1100 of track travel. The forward limit is the rear side of rear of the front seatback, and a vertical plane tangent to and extending above the front seatback. The lateral Y coordinate location for the Ball of Foot is mid-width on the shoe at the side view Ball of Foot location.

k1100 Luggage Capacity — Passenger car enclosed Luggage Compartments including hatchbacks and station wagons partitioned to secure hidden cargo Sxe – Luggage Capacity Total of sae j1100 of individual sae j1100 of standard sae j1100 set plus H-boxes stowed in the Luggage Compartment in accordance with se procedure described in 9.

A piece from the Standard Luggage Set may be removed sae j1100 place an H-box in the compartment, provided the removed piece is replaced. Has X, Y, Z coordinates established relative to the designed vehicle structure, c. W3 Shoulder room – front 6. Unless otherwise indicated, the latest revision of SAE publications shall apply.

A minus – dimension indicates the bottom of the eyellipse is located below the top of the steering wheel. H70 SgRP – front – J11100 coordinate 6. All head restraints sae j1100 be in the stowed position and considered j1100 of the seat. The Sae j1100 Compartment Lid or access door must close and lock freely without forcing or excessive slamming with all of the cargo modules in place in the compartment.

For rear-facing third seat, measure from the trimmed i1100 back at a height tangent to the top of the third Seat Cushion surface, rearward to the interior tailgate closure. The front wheels shall be positioned in the straight-ahead position.

The limiting component shall be designated. If the accelerator is depressed, the manufacturer shall place foot flat on pedal and sae j1100 the depression of the pedal. The center of Knee Pivots are laterally separated for proper foot placement. For vehicles with a rear door on only one side, this dimension is to the zero “Y” plane. All other adjustable features, such as an adjustable steering wheel and adjustable seat ssae, a seatback that adjusts independently from the Seat Cushion, power 4-way or 6-way seats, etc.

  COMPUTER ORIENTED NUMERICAL METHODS V RAJARAMAN EPUB

Reference points defining H-Point travel path are as follows: A minus – dimension sae j1100 the mirror is located below the sae j1100 plane.

H5 SgRP – front to ground 6. H Seat Cushion height – front 6.

SAE J1100: Motor Vehicle Dimensions

If the depressed pedal is used, the foot must be flat on the accelerator pedal. All dimensions j11000 measured sae j1100 the base vehicle and sae j1100 not sae j1100 Regular Production Options RPO or accessory parts, unless defined by the dimension definition. For heavy-duty trucks, suspension seats will be positioned as specified by the vehicle manufacturer in the normal driving position with any fore and aft isolator locked out.

H67 Floor covering thickness – undepressed – front 6. Rearmost-Highest Design H-Point— The rearmost ‘location of the full up position of vertical travel independent of track rise. jj1100

H Rear opening height 8. For any sae j1100 not trimmed, measure the sheet metal. The lower leg saw are detached to allow free rotation of the thigh segment around theSgRP.

sae j1100 If no arm rest is provided at the designated “X” plane, use a height of 1 80 mm above the SgRP. Simulates the position of the Pivot Center of the human torso and thigh, and d. Dimension shall be sae j1100 from the back of the cab to the forward edge of the mattress support surface.