D – 13 Standard Test Methods for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and. All the Controls products ASTM D standard. Enter now!. 26 Nov ASTM D Method C. Reference. Uniaxial Compressive Strength of Intact Rock Core Specimens. (deg). Type. Failure Mode. Rock Type.

Author: Kagagami Tejar
Country: Togo
Language: English (Spanish)
Genre: Video
Published (Last): 27 November 2004
Pages: 394
PDF File Size: 2.35 Mb
ePub File Size: 9.78 Mb
ISBN: 500-7-16758-532-6
Downloads: 57434
Price: Free* [*Free Regsitration Required]
Uploader: Negami

ASTM D, Test equipment Controls

Methods A astm d7012 B determine the triaxial compressive strength at different pressures and Methods C and D determine the unconfined, uniaxial strength. Elastic moduli measured by sonic methods Test Method D may often be employed as preliminary measures of anisotropy.

Method A, triaxial compression c7012, is commonly used to simulate the stress conditions under which most underground rock masses astm d7012. Rock mechanics – Uniaxial and triaxial test systems: Thus the strength values determined are in terms of total stress, that is, are not corrected for pore pressures. The original four standards astm d7012 now referred to as Methods in this standard.

When required, the hardness verification is performed with certified instruments.

The elastic moduli for such rocks should be determined from unload-reload cycles that are not covered by these test methods. Thus, the strength values determined are in terms of total stress and are not corrected for pore pressures. It should be observed that this method makes no provision for pore astm d7012 measurements and specimens are undrained platens are not vented. It is the astm d7012 of the astm d7012 of this standard to establish appropriate safety and health practices 7d012 determine the applicability of regulatory limitations prior to use.

  MICROECONOMIA INTERMEDIA ROBERT FRANK EBOOK DOWNLOAD

The tests provide data in determining the strength astm d7012 rock, namely: Link to Active This link will always route to the current Active astm d7012 of the standard. However, there are some cases where either the rock type or the loading condition of the problem under consideration will require the effective stress or drained parameters be determined.

Dd7012 parameters obtained from Methods Astm d7012 and B are in terms of undrained total stress astm d7012 already mentioned in 1. The elastic constants Methods B and D are used to calculate the stress and deformation in rock structures. Astm d7012 Categories Terms of Use.

The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used.

No other units of measurement are included in this standard.

ASTM International

Platens surface hardness certificate The standards prescribe a minimum surface hardness depending on the type of test to be performed. Astm d7012, laboratory values for intact specimens must be employed with proper judgment in engineering applications. Note 1 — Elastic moduli astm d7012 by sonic methods Test Method D may often be employed as a preliminary measure of anisotropy.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The original four standards are now referred to as Methods in this standard. The test method specifies the apparatus, instrumentation, and procedures for astm d7012 the stress-axial strain and the stress-lateral strain curves, as well as Young’s modulus, Eand Poisson’s ratio. No other units of measurement are included astm d7012 this standard.

  CHITRALEKHA MAGAZINE PDF DOWNLOAD

This option is identified by the Astj code shown on the following table. Agencies that meet the criteria of Practice D are generally considered capable of competent and objective testing.

These test methods do not include the procedures necessary to obtain a stress-strain curve beyond the ultimate strength. In the triaxial mode, a water pressure gradient may be applied to astm d7012 specimen Register or Log in for direct access to additional astm d7012.

Rock mechanics – Highly asrm rock testing systems: Therefore, the dynamic elastic p The original four standards are now referred to ast Methods in this standard. These test methods do not include the procedures necessary to obtain a stress-strain curve beyond the ultimate strength.

These test methods do not include the procedures necessary to obtain a stress-strain curve beyond the ultimate strength. Referenced Documents purchase separately The astm d7012 listed below are referenced within the astm d7012 standard but are not provided as part astm d7012 the standard. Active view current version of standard.